The -r option of netstat displays the IP routing table. Show
On the command line, type the following command. Here is a sample display produced by netstat -r run on machine tenere: Routing tables Destination Gateway Flags Refcnt Use Interface temp8milptp elvis UGH 0 0 irmcpeb1-ptp0 elvis UGH 0 0 route93-ptp0 speed UGH 0 0 mtvb9-ptp0 speed UGH 0 0 . mtnside speed UG 1 567 ray-net speed UG 0 0 mtnside-eng speed UG 0 36 mtnside-eng speed UG 0 558 mtnside-eng tenere U 33 190248 le0 The first column shows the destination network, the second the router through which packets are forwarded. The U flag indicates that the route is up; the G flag indicates that the route is to a gateway. The H flag indicates that the destination is a fully qualified host address, rather than a network. The Refcnt column shows the number of active uses per route, and the Use column shows the number of packets sent per route. Finally, the Interface column shows the network interface that the route uses. Route is a Windows command that displays and updates the network routing table. These activities will show you how to use the route command to display the local routing table. Readings[edit | edit source]
Preparation[edit | edit source]To prepare for this activity:
Display Local Routing Table[edit | edit source]To display the local routing table:
References[edit | edit source]
Use the show ip route EXEC command to display the current state of the routing table. show ip route [address [mask] [longer-prefixes]] | [protocol [process-id]]Syntax Description
Command ModeEXEC Usage GuidelinesThis command first appeared in Cisco IOS Release 10.0. The longer-prefixes keyword first appeared in IOS Release 11.0. The process-id argument first appeared in IOS Release 10.3. Sample DisplaysThe following is sample output from the show ip route command when entered without an address: Router# The following is sample output that includes some IS-IS Level 2 routes learned: Router# Table 68 describes significant fields shown in these two displays. Table 68: Show IP Route Field Descriptions (Continued)
When you specify that you want information about a specific network displayed, more detailed statistics are shown. The following is sample output from the show ip route command when entered with the address 131.119.0.0. Router#Table 69 describes significant fields shown in the display. Table 69: Show IP Route with Address Field Descriptions (Continued)
The following is sample output using the longer-prefixes keyword. When the longer-prefixes keyword is included, the address and mask pair becomes the prefix, and any address that matches that prefix is displayed. Therefore, multiple addresses are displayed. In the following example, the logical AND operation is performed on the source address 128.0.0.0 and the mask 128.0.0.0, resulting in 128.0.0.0. Each destination in the routing table is also logically ANDed with the mask and compared to that result of 128.0.0.0. Any destinations that fall into that range are displayed in the output. Router# Related CommandsA dagger (+) indicates that the command is documented outside this chapter. show interfaces tunnel + What command issued from the command prompt will show the route?Open a command prompt. Type route print. Press Enter. Observe the active routes by destination, network mask, gateway, interface, and metric.
What command issues from the command prompt will show the route that a packet travels from the issuing computer to another computer?The Traceroute command (tracert) is a utility designed for displaying the time it takes for a packet of information to travel between a local computer and a destination IP address or domain.
How to use route command in cmd?To add a route:. Type route add 0.0. 0.0 mask 0.0. 0.0 <gateway>, where <gateway> is the gateway address listed for network destination 0.0. 0.0 in Activity 1. ... . Type ping 8.8. 8.8 to test Internet connectivity. The ping should be successful. ... . Close the command prompt to complete this activity.. Which command is used to determine the route a packet takes quizlet?Traceroute is a command used to determine the path a packet takes as it traverses the network.
|
What command issued from the command prompt will show the route that a packet?
zusammenhängende Posts
Urheberrechte © © 2024 decemle Inc.
